Residential & Commercial
Epoxy Flooring Installation in Los Angeles

Epoxy coating is primarily used in production and warehouses, mainly in industry. They are also being used in homes, especially in rooms that require additional maintenance and cleaning. You can find them mostly located in garages, workshops, kitchens, etc. Only homogeneous, dry, flat, and solid surfaces can be applied to epoxy coatings. It may be stone, concrete, ceramics, etc. Concrete floors are usually used.The concrete coating must be sufficiently stable and have a correct moisture content of 3 to 5%. You have to wait until the concrete dries well or you're using a quick screen. Concrete should also be well prepared through sanding or sandblasting.

The garage flooring is then applied directly to the concrete in several layers. The first layer of epoxy is very thin and only covers the substratum or fills its pores. Depending on the load expected, the second layer of the best epoxy coatings has a thickness of 1 to a few mm. Usually, if necessary, the third layer is applied to higher loads.

Renovating a parking space is always a delicate operation, both for the customer and for companies that must consider many factors so that, when the surface has to be transformed or renewed, there are no surprises.

Another critical step is to find out how the water, sewer, and drainage systems work; This involves knowing the thickness of the existing support, the nature of the support, and the date of the first construction. It would help if you also considered the drainage network, moisture or leakage, bulges or supports, holes, patches, expansion joints, disintegrations, layer consistency, flatness, slope, and identity.

Features of a parking lot with a spectacular finish: Our specialists install a 10 mm thick cement-mortar base, finished with 3 mm self-leveling epoxy resin, sealed with a polyurethane anti-scratch coating.

We maintain good work accessibility, auxiliary equipment, lighting, and access control. Then our supervisors make sure that assignment tasks are performed as the support and location are carefully examined. The presence of cracks is also checked.

Once the surface is prepared by mechanical or chemical means, a preparatory adhesive layer is applied, and the system is selected based on multilayer resins, a rejuvenation of cement mortar with a self-leveling coating or a surface to be finished with garage floor epoxy coating treatments.

Because the preparatory work is done to perfection, any unnecessary extra work is avoided. Color or very innovative pavements that we have for customers can always be tailored to your needs.

1. The application of the base layer is the first step in installing a seamless polymer floor. As such, the so-called epoxy priming is a layer that is not difficult to prepare. For this purpose, mix the composition of both components, leave for 3-4 minutes, and pour the solution onto the floor.

1. A wide flat trowel spreads the base over the working base and attempts to create a uniform layer of 1,5 mm thick. This layer dries for at least 18 hours. The primary purpose is to mask small surface defects and to remove pores. There is approximately 400 g of material consumption per 1 m2 of the area in this case.

1. After 20 minutes, the garage floors are covered with sand; the amount must be approximately 1.5 kg per sqm. Use the access point to move on the flooded epoxy floor surface. When the work is complete, you have to wait until the material is dehydrated, which takes 12 to 24 hours to complete. Walking on the floor during this time is impossible.

1. Excess sand can be removed with a brush from the hard surface. It is again covered with a layer of the epoxy composition after cleaning the sand and dust floor.

1. You can apply a particular film with a pattern on the base layer or use other decorative materials.

1. When mixing components, the finishing layer is filled with a powerful mixer. Each subsequent batch of the solution must be poured to the floor no later than 40 minutes after the previous one.

1. When installing a finishing layer, it is desirable to provide expansion joints; with a doctor's hand, you can adjust the thickness of the layer. Air bubbles must also be removed from the thickness of the solution; a needle roller is used for this purpose.

1. The thickness of the finishing layer is 1-2 mm, with a mass freezing time of 12-24 hours. Walking on the finished floor won't be earlier than three days.

Due to their properties and the materials used in epoxy resins, these floors are considered industrial floors. They are used in multiple high traffic areas such as warehouses, hospitals, restaurants, and pharmacies. Epoxy coating is highly resistant to mechanical damage, chemicals, solvents, acids, and cleaning agents. It also has a high degree of compression and flexural strength. Both can also be used in areas where garage flooring is highly likely.

Epoxy additive resin is the primary material of epoxy flooring. The epoxy resin is added to the aggregate (quartz sand and others) and a hardener. The resin reacts with a healing agent and forms a polymer binder. Other additives like hardeners and the like are often added to the epoxy resin. More and more water-based resin epoxy is being used to create an eco-friendly environment.

The installation of epoxy coatings usually takes 2 to 5 days, depending on the floor's surface area. The self-leveling floor's minimum strength increases after 2-3 days and the maximum after one week. The coating is only ready after 10-12 days for exposure to chemical liquids. To obtain such properties on time, several conditions must be met for epoxy-based self-leveling floors.

1. Thin-layer. Add color and gloss to any product while enhancing viscosity. Thin layer epoxies are needed primarily when using composite wood and epoxy resin. A layer with a thickness of approximately 1 mm is formed during the casting of such an emulsion. Despite the dubious surface thickness, it is highly resistant to mechanical and chemical loads.

1. Thick. This design may not be a single layer, unlike the previous version. Also, one layer thickness is not more than 1 mm at a time. But the floor is very durable by applying multiple layers. Chemical reagents and mechanical loads can be processed efficiently. Such materials are now often used in the construction of homes.

1. Coating with quartz. Epoxy is insoluble, and you can use it to create a real presence on the beach in the room. The lower layer of the composition is added to the quartz sand, thus improving the lower and upper layers' adhesion. The material is resistant to almost any kind of load, making it extremely durable and reliable. Such a floor covering can even be decorated for a specific interior space.

1. Industrial epoxy floors are used in the construction of industrial plants. This type of filler gives the product's concrete color and increased strength. They are resistant to substantial mechanical and chemical loads. At the same time, epoxy floors can be single or double-layered, multi-colored or monotonous, matte or glossy, rough, or very smooth.